RESIN ERA Ultra Clear is a two-component modified, epoxy coating material. When both components are mixed in recommended ratios and cured appropriately at room temperature, an excellent coating or lamination can be achieved on most of the substrates including MDF, glass, metals, plastics, wood, paper stickers, and natural stones. By it, you can make beautiful, gorgeous resin projects and resin crafts.It is only used For Coating Purpose.
APPLICATIONS :
- Coating and lamination of articles
- MDF
- Key-chain
- Metal gift articles
- Paper stickers
- PVC
ADVANTAGES :
- Good colour stability.
- Good flexibility and adhesion.
- High gloss and clarity.
- Thermally stable and suitable to perform in extreme conditions.
- Water and chemical resistant.
- Low odour.
TYPICAL SPECIFICATIONS :
|
TEST |
RESIN |
HARDENER |
|
DESCRIPTION |
BY VISUAL CLEAR, TRANSPARENT |
BY VISUAL CLEAR, TRANSPARENT |
|
VISCOSITY AT 25°C |
800 - 1,200 m Pas |
300 - 600 m Pas |
|
COLOUR |
BY VISUAL COLOURLESS |
BY VISUAL COLORLESS TO PALE YELLOW |
|
DENSITY |
1.00 - 1.20 g/cc |
0.95 - 1.00 g/cc |
MIX SPECIFICATIONS :
|
TEST |
VALUE |
|
MIXING RATIO (RESIN : HARDENER) AT 25°C |
100:50 w/w (2:1) |
|
MIX VISCOSITY AT 25°C |
500 - 800 m Pas |
|
POT LIFE AT 25°C |
25-30 Min |
|
SURFACE DRY AT 25°C |
3-4 hr |
|
TOUCH DRY AT 25°C |
8-10 hr |
|
FULLY CURED AT 25°C |
24-48 hr |
HOW TO USE :
- MEASURE :Take the resin and the hardener in a clean and transparent plastic glass in the measurement of Material for example 100 g of Resin and 50g of Hardener the ratio of 2:1.
- MIXING : After pouring the resin and the hardener into the plastic glass, stir well for 5 minutes to let the bubbles rise to the surface. Make sure that it's mixed properly. After that, you will get 20 to 30 minutes of pot life is you will get a working time of 20-30 minutes after which it will start curing.
- POURING :Before Pouring the resin mix on your piece, make sure that the surface of your piece is leveled. You can now spread the mix over your piece. Wait until the resin gets leveled on the piece on its own. Let the Resin run over the edges of the piece. You may use the hot air gun or a blow torch to remove bubbles (if required), but make sure not to heat resin much.
- CURE : Resinera Ultra clear is surface dry 3-4 hrs. It will need 8-10 hours in a dust free space for surface cure. If you want to do a second layer, you can do it after 8 hours. In 8 hours it will be dry to touch and within 24 hours it will be 100% cure.
TROUBLESHOOTING:
|
PROBLEM |
CAUSE |
|
Uncured after 24 hours to 48 hours |
Wrong mix ratio and | or low ambient temperature (Resin Quantity increases then Ratio or Hardener Quantity decreases then Ratio ) |
|
Fast Cure or Heat up to much |
Wrong mix ratio (Resin Quantity decreases then Ratio or Hardener Quantity increases then Ratio) |
|
Sticky | greasy | hazy surface |
High humidity, Improper Ratio |
|
Dents or Wrinkles on Surface |
Art Piece is not leveled or Mixture of Resin and hardener Poured after or about end of pot life |
PACKAGING : RESIN ERA Ultra Clear is available in 300 gm & 1.5 Kg bottles.
STORAGE AND HANDLING : RESIN ERA Ultra Clear should be stored in a cool and dry place, preferably in a sealed container and should not be exposed to direct sunlight. This product has a shelf life of one year if stored in its original container between 2°C and 40°C away from humidity and excessive heat.
SAFETY : Wear personal protective equipment (Wear mask and gloves). Avoid contact with the eyes and skin. In case of direct contact and irritation, it should be washed off immediately with soap and warm water. Avoid breathing vapors, mist, or gas.
QUICK TIP : Use a larger container if your resin quantity is greater. We recommend this because it generates heat through an exothermic reaction, the sudden increase in heat causes it to harden quickly and become a solid rock within 10-15 minutes.
PRODUCT WEIGHT
- 300 GM
PRODUCT DETAILS
- 2:1
- 200 GM
- 100 GM